Installing VMWare ESX using a Dell DRAC card

Here is a how-to on installing VMWare ESX 3.5 using a DRAC (Dell Remote Access Controller) card to access the server. I was installing a new cluster in a Dell M1000e Blade Centre for work the other day and wrote up this process in order for it to be documented for anyone else doing it in the future.

Just for interests sake the basic specs of the system are:

1 x Dell M1000e Blade Centre
3 x Redundant 2000w+ Power supply units
16 x Dell M600 Blades (Each one has 2 x Quad core Xeon CPUs and 32GB RAM).

1. Connect to the M1000e’s chassis DRAC card.
a. Connect to M1000e chassis DRAC card. (https://x.x.x.x) – use the IP for that particular blade centre’s DRAC card. Login with DRAC credentials.
b. Use the agreed DRAC user credentials, or if this is a new setup, the defaults are username: root password: calvin).

login_drac

2. Select boot order for Blade and power it up
a. Choose the Blade server number that you will be working with from the Servers list on the left side.
b. Click on the Setup tab, and choose Virtual CD/DVD as the first boot device then click Apply.
c. Select the Power Management tab and choose Power on, then click Apply.

configure_boot_order_for_blade

3. Go to iDRAC console of the blade server
a. Click on Launch iDRAC GUI to access the iDRAC for the blade you have just powered on.
b. You will need to login again as this is another DRAC we are connecting to (This time the DRAC is for the actual blade server not the chassis).

launch_idrac_gui

4. Configure Mouse
a. Click on the Console tab near the top of the screen and then click the Configuration button near the top.
b. In the mouse mode drop down, select Linux as the mouse type, then click Apply.

configure_mouse

5. Launch Console viewer
a. From the console tab we can now select the Launch Viewer button.
b. An activeX popup might appear – allow it access and the DRAC console should now appear with the server in its boot process.

6. Mount Virtual ISO media for installation disc (ESX 3.5)
a. Click on Media, and then select Virtual Media Wizard.
b. Select ISO image and then browse to the ISO for ESX 3.5 – this could be on your local drive or a network share.
c. Click the connect CD/DVD button to mount the ISO.
d. Your boot order should be configured correctly to boot off this ISO now. (*Optional* You could always press F11 whilst the server is booting to choose the boot device anyway).

attach_virtual_media_iso

7. Reboot the server if the boot from virtual CD/DVD has already passed
a. Go to Keyboard – Macros – Alt-Ctrl-Del to do this.

8. ESX install should now start.
a. Press enter to go into graphical install mode
b. Select Test to test the media (The ISO should generally be fine).
c. Select OK to start the install.
d. Choose United Kingdom Keyboard layout (or whatever Keyboard layout you use).
e. Leave the mouse on generic 3 button USB.
f. Accept the license terms.

esx_install_start

esx1

9. Partitioning
a. For partition options, leave on “Recommended”. It should now show the Dell virtual disk of 69GB (in this case) or the Dell RAID virtual disk / disk configuration.
b. Say “Yes” to removing all existing partitions on the disk. (That is if you don’t mind formatting and completely clearing out any existing data that may be on this disk).
c. Alter partitions to get the following best practice sizes: (See http://vmetc.com/2008/02/12/best-practices-for-esx-host-partitions/)
d. Note: It doesn’t matter if these sizes are 2-3MB out for some. The installer deviates these sizes slightly. The swap partition should have 1600MB minimum though.
e. Next page is Advanced Options – Leave as is (Book from SCSI drive).

esx_partitions_recommended

10. Network Configuration
a. Setup network configuration
b. IP address (x.x.x.x) – whatever IP you are assigning this particular ESX Host.
c. Subnet mask: 255.255.255.0 for example.
d. Gateway:  Your gateway IP address (x.x.x.x)
e. Primary DNS:  (x.x.x.x)
f. Secondary DNS: (x.x.x.x)
g. Hostname: localhost.localdomain for example : ESXhost01.shogan
h. VLAN ID – Leave this blank if you are not using VLANs. If you are, then specify the VLAN here.
i. Create a default network for virtual machines – Unless you have a specific network configuration in mind leave this ticked on.

11. Time zone
a. Set Location to  your location.
b. System clock uses UTC is left as ticked.

12. Root password
a. Set default root password . (This is your admin password)!

13. Finish installation
a. Next page is “About to Install”
b. Check the information is all correct and click Next if all looks fine.

14. Change boot order back and restart the blade server.
a. Via the iDRAC page, change the boot order back to Hard disk for the blade so that it will reboot using the server’s RAID hard disks instead of the ISO.
b. Reboot the host by pressing the Finish button back in the console.
c. Disconnect the Virtual CD from the Media option in the console menu.
d. Watch the console while the server reboots to ensure no errors are reported on startup.

If all went well, you should now have an ESX Host booted to the console. Press Alt-F1 to access the command line (you will need to login as root or any other user you setup).

You can now access your server via the web browser (https://x.x.x.x). From here you can download the Virtual Infrastructure client to manage the ESX Host with.

This host could now be further configured and added to an ESX cluster for example. SANs could be assigned and vMotion setup so that HA (High Availability) and DRS (Distributed Resource Scheduling) can be put to good use!

5 Comments

  1. Hi Shogan,

    Thanks for the nice walk through of esxi installation drac.

    Hope to see more good articles from you.

    Thanks & Regards,
    Santosh Maid

  2. Hi Santosh,

    No problem – I hope it was useful. Definitely more to come – just a bit busy at the moment with a new job as well as wedding coming up!

    Cheers,
    Sean aka Shogan

Leave a Reply

Your email address will not be published. Required fields are marked *

*